The power amplifier is an indispensable key component of the millimeter wave band transmitter. The output power determines the range and anti-interference ability of the entire system. In the millimeter wave system, as the frequency increases, the output power of a single MMIC chip can no longer meet the actual use requirements, especially the non-atmospheric window frequency band, because the transmission of electromagnetic waves in this band is seriously attenuated by the absorption of oxygen molecules and water vapor molecules . Generally used in military security work and short-range radar detection and communication systems, the output power of the corresponding device is also small. Therefore, the power synthesis method is often used to combine multiple amplifier units to achieve a larger power output.
The amplifier works in the V band and is used for a close-up detection system. It fully utilizes the attenuation characteristics of the non-atmospheric window band to achieve confidentiality and anti-interference.
1 Design of power amplifier
1.1 Technical index requirements
According to the basic requirements of the system, the main technical indicators of the amplifier: operating bandwidth 2 GHz; output power ≥200 mW; gain 20 ~ 25 dBm; input and output port WR15.
1.2 Selection of power devices
In order to meet the requirements of technical indicators, a three-terminal FET power amplifier device with a wide operating frequency band is selected. The FMM5715X of Eudyna Devices was selected as the power synthesis unit. The FMM5715X is a multi-tube synthesized power monolithic matched to 50 Ω within the port impedance. Operating frequency is 57 ～ 64 GHz; operating temperature range: -45 ～ + 85 ℃, storage temperature range -55 ～ + 125 ℃; maximum allowable input power 3 dBm; can work with single power supply, bias 3 V / 150 mA at DC Under the conditions, the typical performance P1 dB at 60 GHz is 16 dBm, the saturation power is 17 dBm, and the small signal gain is 17 dB. The characteristic parameters are shown in Figure 1.
1.3 Synthetic network design
1.3.1 Overall scheme of synthetic network
In the V band, the output power of a single tube is far from the power output demand. Even if it is a MMIC power device using multiple tube synthesis, the single device cannot meet the technical specifications. Therefore, the use of multi-device power synthesis technology is an inevitable choice for the completion of this project. At present, the more mature power synthesis technology is to use a two-way bridge with a better port standing wave, and realize multi-way synthesis by multi-stage cascade. The designed amplifier adopts two-way binary multi-level power synthesis technology based on the waveguide low-loss transmission line structure. The synthesis network consists of two parts, a power driving stage and a power amplification synthesis stage, each part includes a 3-stage binary network, which is composed of waveguide branch lines. Bridge and waveguide-microstrip transition. The synthetic network block diagram is shown in Figure 2.
For 8-way power distribution, the network loss of each stage is counted as 0.3 dB, and the path loss is calculated as 0.5 dB. To saturate all power devices during synthesis, the input power of FMM5715X should be> 2 dBm. The power at the input of the power distribution network is 12.4 dBm. Obviously, the single-channel FMM5715X driver stage is sufficient to meet this requirement.
When all power devices in the synthesis network are in the saturated working state, the single-stage loss is 0.3 dB, the three-stage power synthesis, the synthesis efficiency due to loss is 80%; 3 dB and 30 ° respectively, resulting in a corresponding synthesis efficiency of 90%; for 8-way power synthesis, the total synthesis efficiency is
When the device works in saturation, the 8-channel composite output is 17 + 7.07 = 24.07 dBm or 255 mW, which meets the requirements of the technical indicators. The loss of each part of the circuit is 4 8 dB, and the small signal gain of the entire synthesis amplifier is about 29.2 dB.
Electric Kettle are made by food grand stainless steel and Polypropylene. It helps you to have a 1.8L bottle of boiled water in 5 minutes. Type 201 Stainless stell is the main material for the electric kettle housing. sometimes called a tea kettle or teakettle, is a type of pot, typically metal, specialized for boiling water, with a lid, spout, and handle, or a small kitchen appliance of similar shape that functions in a self-contained manner. Kettles can be heated either by placing on a stove, or by their own internal electric heating element in the appliance versions.
Features:
360-degree swivel base: Great way with cordless pouring; kettle lifts off base for cord. Separate base to move kettle conveniently, 360°rotation design.The cord can be wrap neatly into the base bottom for easy storage. The concealed stainless steel heating element brings fresh hot water with no metal Taste.
Soft Handle for easy using: Comfortable stay-cool handle; brushed stainless steel finish. Cool-touch buttons and ergonomic stay-cool handle.
Large Capacity for Multiple Cups: 1.8 L large capacity, with Max. water level inside the kettle. almost 1.5x the size of most tea makers. Brew up to 6oz at once! Perfect for small gatherings & parties!
Fully Stainless Steel Faster Boils: Stainless Steel Interior cover with no plastic taste. Boils water rapidly, save more time and energy. Faster than the microwave & safer than your traditional stovetop teapot.
On/off switch with LED light.: Automatic On/Off switch makes life easier. No need standing by for hot water. It shuts down when reaches a full rolling boil. Boil-dry and overheat protection to ensure the safety use.
Time Saver & Higher Safety: 1500 watts energy efficient for quick heat-up time brings water to a boil, Fast boil, auto shut off and boil dry protection technology with three-prong plug.
Brushed stainless steel housing
Applications
Making hot water for tea brewing.
Making Coffee.
Cool milk-tea.
Steaming eggs.
Any occation if you need hot water in short time.
Any color of plastic is available to produce but in big quantity. Its
Electric Kettle
Electric Kettle,Stainless Steel Electric Kettle,Electric Boiler,Big Capacity Electric Kettle
Guangzhou Taipeng Electrical Appliances Technology CO., LTD. , https://www.kettles.pl